Raspberry Pi

The scope of this article is the installation steps taken to produce a local area network using a RaspberryPi 3, running Raspbian Jessy Lite, with a bridged internet connection via an Ethernet cable to facilitate both the Hackers & Designers workshops around basic Unix and program skills for designers, and the Frankenstein Bot workshop by Constant.

Code blocks that begin with "$" denote terminal, command line instructions, all other code blocks denote configuration files and/or program source code.

In all locations where "vi" is used, feel free to use another text editor of your choice (ex. nano).

Setting up the network

---

These instructions are taken largely from here, but are reiterated in the case article disappears from the internet.

We need to tell dhcpcd to ignore the wlan0 interface.

$ sudo vi /etc/dhcpcd.conf

Add the following line to the bottom of the file:

denyinterfaces wlan0

wlan0 will need a static ip address.

$ sudo vi /etc/network/interfaces

The file should contain, everything else can be commented out or deleted:

   auto lo
   iface lo inet loopback
   allow-hotplug eth0
   iface eth0 inet dhcp
   allow-hotplug wlan0
   iface wlan0 inet static
       address 10.1.1.1
       netmask 255.255.255.0
       network 10.1.1.0
       broadcast 10.1.1.255

Install hostapd, and configure it.

$ sudo apt-get install hostapd

$ sudo vi /etc/hostapd/hostapd.conf

   interface=wlan0
   driver=nl80211
   ssid=Hackers & Designers
   hw_mode=g
   channel=6
   ieee80211n=1
   wmm_enabled=1
   ht_capab=[HT40][SHORT-GI-20][DSSS_CCK-40]
   macaddr_acl=0
   ignore_broadcast_ssid=0

$ sudo vi /etc/default/hostapd

Uncomment and set the following value:

DAEMON_CONF="/etc/hostapd/hostapd.conf

Install and configure dnsmasq.

$ sudo apt-get install dnsmasq

   interface=wlan0
   listen-address=10.1.1.1
   bind-interfaces
   server=8.8.8.8
   domain-needed
   bogus-priv
   dhcp-range=10.1.1.50,10.1.1.250,12h

For the purposes of the Frankenstein "hovel" bot, also uncomment:

   log-queries
   log-dhcp

Setup IPv4 forwarding.

$ sudo vi /etc/sysctl.conf

Uncomment the following line.

net.ipv4.ip_forward=1

Execute the following.

   $ sudo iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
   $ sudo iptables -A FORWARD -i eth0 -o wlan0 -m state --state RELATED,ESTABLISHED -j ACCEPT
   $ sudo iptables -A FORWARD -i wlan0 -o eth0 -j ACCEPT
   $ sudo sh -c "iptables-save > /etc/iptables.ipv4.nat"

To ensure the forwarding persists beyond restarts.

$ sudo vi /etc/rc.local

Add the following line before exit(0).

iptables-restore < /etc/iptables.ipv4.nat

Restart and verify the network is working.

$ sudo reboot

Frankenstein Bots (IRC)

---

The Frankenstein bot project requires an IRC server. I use UnrealIRCd for this.

Install ssl.

$ sudo apt-get install libssl-dev

Download UnrealIRCd, for example (but maybe check the versions etc.).

$ wget 'https://www.unrealircd.org/unrealircd4/unrealircd-4.0.4.tar.gz'

Untar, change directory.

   $ tar -zxf unrealircd-4.0.4.tar.gz 
   $ cd unrealircd-4.0.4/

Configure.

$ ./Config

It will ask a lot of questions, I accepted all the defaults.

Build, Install.

   $ make
   $ make install

Start.

   $ cd ~/unrealircd
   $ ./unrealircd start

It may complain you need to create a configuration file. You can find how to do that here

Creating Unix users

---

You may desire to create one or more of your own users for bots or other things.

$ sudo adduser --home /home/jbg jbg

You may also need to add the user to a group for example "sudo".

$ sudo usermod -G sudo jbg

Install Python Modules

---

Some of the Frankinstein bots require the irc.bot Python module.

Download and install pip.

$ wget https://bootstrap.pypa.io/get-pip.py

$ sudo python get-pip.py

Install irc python module.

$ sudo pip install irc

Install Fun Command Line Utilities (H&D Terminal workshop)

---

$ sudo apt-get install figlet

$ sudo apt-get install mailutils

$ sudo apt-get install cowsay

$ sudo apt-get install jp2a

FTP

---

For FTP simply follow the instructions here.

Etherpad

---

Install Node.js. Maybe check the version, perhaps there is something newer.

$ wget https://nodejs.org/dist/v4.4.7/node-v4.4.7.tar.gz

$ tar -zxf node-v4.4.7.tar.gz

$ cd node-v4.4.7/

$ ./configure

$ make

$ sudo make install

Get dependencies for Etherpad.

$ sudo apt-get install gzip git curl libssl-dev pkg-config build-essential

Install Etherpad.

$ git clone git://github.com/ether/etherpad-lite.git

$ cd etherpad-lite/

Run it!!

$ bin/run.sh